Parting out a 72 GS 350

Discussion in 'Car Part-Outs' started by RACEBUICKS, Mar 8, 2013.

  1. buickapollo455

    buickapollo455 Well-Known Member

    Re: Parting out a 72 GS 350 ..... air cleaner

    need gs dual snorkel air box lower with dual ends , if lid is different than 455 need lid too.
     
  2. RACEBUICKS

    RACEBUICKS Midwest Buick Mafia

    Ok so going on vacation and weather and now I will try to answer all the questions on the parts you all wanted to check out. Give me some time I will start as far back as I can and roll forward thanks.

    ---------- Post added at 03:29 PM ---------- Previous post was at 03:19 PM ----------

    I do have the dipstick and tube. They look nice however until I get the front end off I cant get to them because the frame is bent and shoved the engine over to the steering column

    Nothing of any value. I may have one in my swap meet trailer let me look when I get time.


    Will take $100 for the pair plus shipping where are you located?

    ---------- Post added at 03:40 PM ---------- Previous post was at 03:29 PM ----------

    $650 for the hood as is complete In primer ready to paint $1200

    I should have several of those plates. Not so sure about the latch and stuff need to look around

    Sold the PS pump assemble already I will look thru some bracket boxes I have and see if I have one.

    SOLD already
     
  3. 71SkylarkConv

    71SkylarkConv Roll Tide

    Mike, the latch and rod are removeable. Just need the stamped sheetmetal piece that's about 24" long and has a stop on the top.

    Art

     
  4. RACEBUICKS

    RACEBUICKS Midwest Buick Mafia

    I have several $25 shipped
     
  5. 71SkylarkConv

    71SkylarkConv Roll Tide

    I'll take one. PM sent.

    Art

     
  6. 71SkylarkConv

    71SkylarkConv Roll Tide

    Paypal sent.
    Thanks, Mike.
     
  7. 71SkylarkConv

    71SkylarkConv Roll Tide

    Got it. Thanks Mike.\

    Art
     
  8. shadewolf

    shadewolf Well-Known Member

    just out of curiosity whats left of the car???? any pics of whats available?
     
  9. wheelz

    wheelz 'B' is for Buick.

    Hi Mike! ANY CHANCE the GLOVEBOX DOOR GROMMET is still good on this car? If so, would you wanna cut the metal around it like maybe 2x2x2x2 and send it to me? I have asked a few members to try to locate a few grommets for me in case I bust one up... Please Lemono!

    Wheelz, Tampa Bay
     
  10. RACEBUICKS

    RACEBUICKS Midwest Buick Mafia

    Its still nearly complete what are you looking for? I just drug another 72 GS350 home too.

    ---------- Post added at 09:07 AM ---------- Previous post was at 09:06 AM ----------

    They arent that hard to remove are they?


    And before everyone gets your panties in a wad this new car is just as rusty as the last one. Cars like this are not worth saving
     

    Attached Files:

  11. wheelz

    wheelz 'B' is for Buick.

    Hi Mike.. I ruined two trying to remove them. They are kinda buggirs to remove in one piece... Duane agrees when in fact, he cuts the metal out around the grommet and then he carefully removes the metal bit by bit until he has just the grommet. he softens them in lacquer thinner so they can snap back in... YA. its a pain but I need one ASAP because its holding me up finishing the interior of George Lanoues (San Jose CA) 72 GS 455.

    I'd like TWO in case I mess one up...

    Canya HELP ME OUT here Ole buddy Ole pal??


    Wheelz, Tampa Bay
     
  12. jeffpye

    jeffpye Well-Known Member

    Hey Mike,
    I need a set of headliner bows? Any chance you might still have some?
     
  13. RACEBUICKS

    RACEBUICKS Midwest Buick Mafia

    time to get them out is the main thing but oh yea I have several cars worth
     
  14. wheelz

    wheelz 'B' is for Buick.

    Mike...AND EVERYONE ELSE. . . Thanx to Roberta, here is a pix of what I am looking for:I am looking to purchase AT LEAST TWO...so I can mess one up!
     

    Attached Files:

  15. jeffpye

    jeffpye Well-Known Member

    I really need a set with the clips. How long are you talking to get them out?
     
  16. xplantdad

    xplantdad Newbie with Buicks!

    Are the valve covers the same as a 71? I 'd like to have an extra set for my car...to clean up and paint...
     
  17. shadewolf

    shadewolf Well-Known Member

    is the new 72 gs frame any good??? maybe one of the two frames might have usable sections for my frame.
     
  18. RACEBUICKS

    RACEBUICKS Midwest Buick Mafia

    Well part of the issue is I had to let the kid I had helping me go. The economy doesn't allow me to have a parts kid anymore. So when I get some time I will try and get out there to get them pulled. Sorry about the delay

    ---------- Post added at 07:44 PM ---------- Previous post was at 07:44 PM ----------

    I have no idea really

    ---------- Post added at 07:45 PM ---------- Previous post was at 07:44 PM ----------

    I have several around here for sure
     
  19. RACEBUICKS

    RACEBUICKS Midwest Buick Mafia

    OK I have hired a kid to help with my dismantling of cars . I will try to get things off in a timely manner. Let the shopping begin.
     
  20. shadewolf

    shadewolf Well-Known Member

    Looks like the pics of the new parts car has a n25 bumper. if so how much w/all the brackets and stuff.
     

Share This Page