1970 LeSabre in a scrap yard. Low miles & lots of good parts.

Discussion in 'Parts for sale' started by oldspackrat, Feb 26, 2016.

  1. tufbuick

    tufbuick FUHGEDDABOUDIT, Y'ALL !!!

    How much for the disc brake set up ?

    Are they the same as a 1969 Electra 225?

    Will they bolt right on ? If so i'm interested.
     
  2. oldspackrat

    oldspackrat Well-Known Member

    tufbuick,
    As far as I know they will fit all of the big body (B?) G.M. cars from that era. Not sure what all years are the same & I would urge you to do some research to confirm all this. When I took the brakes apart, I had my helper step on the pedal to keep the wheels from turning as I loosened the lugnuts & everything seemed to work like it should. That being said it all could use a good cleaning & inspection before installation. I would like to get $300.00 for all the brake parts in the picture plus shipping or pick up in Indianapolis. These pieces are HEAVY & I'm sure shipping will not be cheap.
    Thanks,
    Scott
    c. 317-727-7041
     
  3. tufbuick

    tufbuick FUHGEDDABOUDIT, Y'ALL !!!

    How much for just the rotors as I don't need the rest of the stuff ?
    That would keep the shipping cost down.
     
  4. Hawken

    Hawken Hawken

    I am interested in the seat belts and retractor covers. Can you please post or PM me (for email address) the certification tag on the driver's or passenger front seat belt (it is affixed to the belt).

    I am also interested in the brake proportioning valve (I only see the 'hold off' valve present). It might be mounted on the inner engine compartment driver side frame area.

    Thanks.
     
  5. ginpolejumper

    ginpolejumper Founders Club Member

    Its King Tuts cat....
     
  6. staged70

    staged70 RIP

    Sorry I forgot to inform you I was passing on the seat belts
     
  7. REFORMULATED400

    REFORMULATED400 Silver Level contributor

    Inline for the AM- FM radio if its still available. PM sent
     
  8. oldspackrat

    oldspackrat Well-Known Member

    Pulled the pass. fender & cut out the heel of the driver fender for a customer. Pulled the very clean gas tank & rear bumper too. Almost feel guilty tearing it all apart but I know it will help others with their cars. I will probably cut the super clean quarters out soon.
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
     
  9. Drachen

    Drachen Well-Known Member

    Judging by the head, tail and position of the forelegs, it's probably a cat.
    Mine in sleeping on the bed next to me with her legs tucked up under her,
    in pretty much the same position.

    She isn't mummified, but she sleeps so much it's hard to tell sometimes.:grin:
     
  10. oldspackrat

    oldspackrat Well-Known Member

    Still have lots of nice interior pieces from this car. Super nice rear side panels, almost new rear seat back & bottom, kick panels, AC ductwork, perfect dash pad, rear arm rests, etc...
     
  11. oldspackrat

    oldspackrat Well-Known Member

    Trunk floor cut out now, along with pass. front inner fender, good patch under the battery tray, lower fender patches, & a few other parts.
    [​IMG]
    [​IMG]
     
  12. Notch

    Notch Well-Known Member

    id be interested in the ac hoses (complete) if they're available? and the floor covering for the boot, and the jack, lug nut wrench and spare wheel hold down. Let me know. Thanks. Andrew
     
  13. oldspackrat

    oldspackrat Well-Known Member

    Notch,
    The condenser & associated hose were damaged in the crash. If & when I go back there I'll check the other hoses & grab all that are in good condition. I do have the trunk mat. It is still pretty nice but does have a couple cuts/splits in it. I don't think there are any missing pieces though. I'll try to get pix shortly. The jack & all associated parts have been sold already, sorry.
     
  14. Notch

    Notch Well-Known Member

    Thanks. It was the pipes that connect to the compressor I'd be keen on. No trouble with the rest; keen on the Matt still. I'll pm you. As I just want to check measurements for my electra.
     
  15. dmva

    dmva New Member

    I'd be interested in the rear quarter moldings at bottom, between rear wheel wells and rear bumper - both side.

    Also, emblem from rear bumper.

    Thanks.
     
  16. 70 Sabre

    70 Sabre Member

    Hi Scott, wondering if you still have the two rear wheel well chrome trim pieces? How about the two pieces of chrome on the top of the front fenders just under the windshield (they line up with the back of the hood)? The shifter lever? Rear tail light lenses? The "custom" emblems on the rear quarters ( they were right under the lesabre emblems)? Is the L rear view mirror clean & still available? How about the glove box door (really only need the locking mechanism)? Thanks!
     
  17. oldspackrat

    oldspackrat Well-Known Member

    dmva,
    Sorry all those parts have been sold. :(

    70 Sabre,
    Going back tomorrow to cut the quarter panels off the car & will grab all the other parts on the list. I sold the original shifter handle but have another identical one from a different '70 Lesabre. It is not quite as nice but might work? I'll get pix of everything once I gather it all together.
     
  18. oldspackrat

    oldspackrat Well-Known Member

    Doors are left, front seat, steering column, engine & trans, that's about it.[​IMG]
    [​IMG]
    [​IMG]
     
  19. nickbuickgs

    nickbuickgs nickbuickgs

    How about all the engine lifting bracket on the manifold ,TCS switch , & air cleaner pcv hose . Plastic spark plug wire holders

    Thanks
    Nick
     
  20. austingta

    austingta Well-Known Member

    Iron ore to iron ore I guess... wow
     

Share This Page