72 interior door panels

Discussion in 'Interior City' started by scubasteve455, Jul 11, 2019.

  1. scubasteve455

    scubasteve455 Well-Known Member

    I have new inner door panels from Legendary. Kinda confused on how the fasteners glue to the cardboard backing. i plugged in the new plastic orange tubes in the doors. Do the tiny clips slide behind the cardboard? B0B3FA55-20FD-4F36-8DAD-8894077FAFFE.jpeg
     
  2. steve covington

    steve covington Well-Known Member

    They don't glue to the cardboard. The slot in the clip goes into the hole, and then you push it in the direction of the flat.
     
  3. scubasteve455

    scubasteve455 Well-Known Member

    Thanks Steve that makes sense. I looked at the old panels . Did not know witch way to go. I see now how they punched it.
     
  4. scubasteve455

    scubasteve455 Well-Known Member

    stupid is Stupid dose.
     
  5. scubasteve455

    scubasteve455 Well-Known Member

    So Steve i pulled in the direction of the curvature in the cardboard. not the straight intrusion.
     
  6. 72STAGE1

    72STAGE1 Runnin' with the Devil

    No, I believe that is incorrect .....even tho I am not Steve......Toward the edge of the panel ......but I believe you are in over your head Sir and should just send the entire car to my garage and give up.....
     
    scubasteve455 likes this.
  7. scubasteve455

    scubasteve455 Well-Known Member

    Looking back. Yes you can get way over your head. Cars are Money Pits. But better than spending on Wine and Women.
     
  8. scubasteve455

    scubasteve455 Well-Known Member

    I’ll take that as a Compliment. x2 Van Halen. Thank you. Means a lot.
     
    72STAGE1 likes this.
  9. gstewart

    gstewart Well-Known Member

    The down factor about owning one of these classic muscle cars is that if u cannot do most of the work yourself, U better have a money pit or a rich uncle.
     
  10. scubasteve455

    scubasteve455 Well-Known Member

    Or a Rich Honey Bunny
     
  11. gstewart

    gstewart Well-Known Member

    Sugar Momma !!!!
     
    scubasteve455 likes this.
  12. scubasteve455

    scubasteve455 Well-Known Member

    That’s it!
     
  13. Red Skylark

    Red Skylark Well-Known Member

    Did your door panels come already with the holes cut for window cranks, handles, armrests etc? If not how did you cut the holes.
     
  14. scubasteve455

    scubasteve455 Well-Known Member

    Well just the Arm rest. My car has a Power windows . Everything is perforated on the back side. So you know where to cut.
     
  15. Red Skylark

    Red Skylark Well-Known Member

    I only opened the box and pulled one of the back panels out and noticed it wasn't cut.
     
  16. scubasteve455

    scubasteve455 Well-Known Member

    But it’s open for option. They perforated the panel for the correct choice. I will look at my panels today. chime back. Because mine are still not together.
     
  17. scubasteve455

    scubasteve455 Well-Known Member

    You have window cranks. I do not.
     
  18. scubasteve455

    scubasteve455 Well-Known Member

    Are yours made by legendary?
     
  19. Red Skylark

    Red Skylark Well-Known Member

    They are Legendary. I have window cranks also.
     
  20. scubasteve455

    scubasteve455 Well-Known Member

    Red your old panels are your best Stencil. Do you have the door panels. ( old) Look at them and measure. Buy a Hole saw set at Lowe’s and Home depot. or Harbor freight. Put on a drill. Start spinning slow then speed up when almost through. So the circle is clean. Not jagged.
     

Share This Page