Bbb timing cover, rebuilt pump

Discussion in 'Parts for sale' started by Bens99gtp, Mar 16, 2018.

  1. Bens99gtp

    Bens99gtp Well-Known Member

    I have for sale a very clean, heavily modify Bbb timing cover with pump gears and kb booster plate. This is used but very lightly.......has a few hrs of break in and adjusting run time, a few 1st gear hits on the road, 1 1/4 mile pass, 2 1/8th miles passes. We went to a more race oriented oiling system.

    All the work on this cover and pump were done by Mike Phillips from AMP in early 2017. It appears there is not a single passage that has not been enlarged, smoothed, radiused, etc. Both the surfaces on the cover and filter housing were all machined to be perfectly flat. Rope seal was also replaced with TA modern front seal. Gears look perfect, and has oil hole in idler gear to help lube.
    Hopefully the quality of work shows in the pictures.

    No stripped or broken bolts.

    On my motor this pump was holding warm pressure ( oil temp 160) 25psi at idle, 50psi at 3000, 70psi at 6000.

    I stripped all the paint off, used wire brushes, paint thinner, and cleaner. No blasting sand or glass at all, I took the pump apart to fully clean and check over after cleaning the cover but before priming, and then primed the cover. Pump gears were lightly lubed with Brad Penn oil, then the pump was packed b4 reassembling.

    Should be ready to paint, bolt on and enjoy.

    Asking 400 shipped and insured to the lower 48, will ship farther if you cover the extra shipping cost. Will accept paypal f&f, or you cover the 3%, or postal money order.
     

    Attached Files:

  2. sriley531

    sriley531 Excommunicado

    Interested. What regulator spring is in it? Am I seeing correctly that it's showing about .002" max pump gear clearance?
     
  3. Bens99gtp

    Bens99gtp Well-Known Member

    Correct that is the clearance. I think it's a white spring.....Mike set everything up. our motor has .003 rods and mains and with 20w50 synthetic those are the pressures we had.
     
  4. sriley531

    sriley531 Excommunicado

    Thanks Ben, let me check on some things and I'll get back to you asap.
     
  5. Bens99gtp

    Bens99gtp Well-Known Member

    Np, I will have to check I might have other springs if needed, if not an adjustable spring setup from TA IS only 20, if the pump spring setup is or becomes an issue I will drop 20 off the price to cover the cost of the adjustable TA setup so you can get whate very pressure you need
     
  6. Harlockssx

    Harlockssx Brother Graw Mad

    If sriley531 doesn't get it, please put me next in line.
     
  7. Bens99gtp

    Bens99gtp Well-Known Member

    Sounds good your second inline
     
    Harlockssx likes this.
  8. sriley531

    sriley531 Excommunicado

    Ben, thanks for answering my questions. I'm going to hold off at this time, harlock you are up
     
  9. Bens99gtp

    Bens99gtp Well-Known Member

    Pm sent
     
  10. Harlockssx

    Harlockssx Brother Graw Mad

    Replied, thanks!
     
  11. Harlockssx

    Harlockssx Brother Graw Mad

    Payment sent
     
  12. Bens99gtp

    Bens99gtp Well-Known Member

    Awsome, I will get it boxed up and send you tracking number, mostly likely be tomorrow b4 I can get to FedEx
     
    Harlockssx likes this.
  13. Bens99gtp

    Bens99gtp Well-Known Member

    Cover sold and sent,
     

Share This Page