Dual Exhaust

Discussion in 'Small Block Tech' started by lesabre 69, Dec 13, 2018.

  1. lesabre 69

    lesabre 69 Member

    Someone no if dual exhaust from skylark 69 fits lesabre 69 350-4
    The first time i written on english butt hope fore same respons.
    Hi frome Sweden
     
    Nailhead Ronnie likes this.
  2. alec296

    alec296 i need another buick

    Tailpipes won’t work well, and are shorter.
    The pipes from exhaust manifolds to mufflers will probably work but will need to be lengthened.
     
  3. lesabre 69

    lesabre 69 Member

    Nice can't find a system in sweden to Lesabre .
    I was going to take the first tube, extend to the rear axle and straight out behind no mufflers.
    Do you think the bend over the axel woke out?
    run with single straight pipe just a small silencer just crusin and have good ear protection like a good stereo lol
     
  4. Houmark

    Houmark Well-Known Member

    Du kan købe rør der kan clampes sammen, i Biltema.. De har også ophæng, lyddæmpere osv.. Der findes også bagtøjs bøjninger, som slår et loop over bagtøjet, og ender i lige rør igen..

    You can buy tubing, that is meant to be clamped togtheter in Biltema, they've also got silencers, brackets and so on..
     
  5. lesabre 69

    lesabre 69 Member

    Know, but what I need most is the pipes from the manifolds and down. Have y-tubes that are rubbish.
    Will probably fix it somehow, there is a problem for finding solutions.
     
  6. SpecialWagon65

    SpecialWagon65 Ted Nagel

    Greetings from Cincinnati, welcome here. Sounds like you want it to be very loud!
     
  7. SpecialWagon65

    SpecialWagon65 Ted Nagel

    alec296 likes this.
  8. lesabre 69

    lesabre 69 Member

    Thanks
    It's a later issue but easier to fix
    when I have new downpipes and the bended pipes over the rearaxel
     
  9. Fox's Den

    Fox's Den 22 years of racing the same 355 Buick motor

    You can probably make the system work you will just have to add extension pipes from muffler to tail pipe. May also need to add extension pipe from front to mufflers too.
     
  10. lesabre 69

    lesabre 69 Member

    Check this and get a little measure to do
     
  11. sean Buick 76

    sean Buick 76 Buick Nut Staff Member

    It might be easier to have a shop custom bend you a system... I just did this on my 2012 gmc and custom bent was a great fit and low cost.
     
  12. gsjohnny1

    gsjohnny1 Well-Known Member

    they never made duals for the 350 engine, only 455.
    you could use walker exhaust p/n's
    2 of 43397, tailpipes
    1 of 43315, over axle p/side
    1 of 43500, over axle d/side
    2 of 21617 mufflers
    front pipes will have to be made or possible front pipes of 70-72 gs 350
    1 of 46270, p/s
    1 of 47341, d/s
    check with Waldron exhaust in Michigan I think
     
    Paul Stewart likes this.
  13. lesabre 69

    lesabre 69 Member

    Talked to a local guy and we take the GS 350 first pipes ,

    make them a little bit longer.Then there will be a wildcat system the rest.
    Hope it works Merry Christmas guys
     
    DasRottweiler and alec296 like this.
  14. alec296

    alec296 i need another buick

    A H balance tube or X pipe might help performance alittle. And with duals from single exhaust could use a jet up in carb since air flow will improve. Could probably at 2 degrees of timing also.
     
  15. lesabre 69

    lesabre 69 Member

    Trix and fix.
    newly renovated, 0.30 drill
    10: 1 pistons and comp 268 h.
    73 bottom and heads from 68 distributor 1111260 think it is 30° advance have to check. have an extra 1111334 , some one wants to be rebuilt .
    Works well, but better when i removed muffler and silencer. Has set the ignition at 6 °
     
  16. alec296

    alec296 i need another buick

    That cam really perfers headers to work best, it needs the extra scavenging . Straight pattern.
     
  17. Nailhead Ronnie

    Nailhead Ronnie Life's 2 Short. Live like it.

    Merry Christmas my buick brother
     
    lesabre 69 likes this.

Share This Page