Parting Out 72-350 Motor, Some Nice Pieces

Discussion in 'Parts for sale' started by AzChevs, Sep 13, 2017.

  1. AzChevs

    AzChevs Well-Known Member

    This was a low mileage 1972 Skylark 350 4 brl complete motor that I was trying to sell whole locally. I had sold the emission set up here a few months back, the rest is available including carb for $50.00, nice flex plate for $30.00 bolts are extra 8.00 for the set, intake 60.00, A/C lower pulley $30.00, water pump pulley $25.00, exhaust manifolds $100.00 pair including bolts. Let me know if you need anything else and I can post a price for you. Paypal gladly accepted as sales, Joe 602-298-7090
     

    Attached Files:

  2. rjm

    rjm Active Member

    Az, Iwould be interested in the pullies and a/c brackets if you have them. I will be installing a/c in a non a/c car, so I need all the associated a/c pullies and brackets. Thanks
     
  3. AzChevs

    AzChevs Well-Known Member

    Rick, I had sold the ones off the motor but do have another set, I will put my hands on them tomorrow let you know exactly what I have. Thanks
     
  4. rjm

    rjm Active Member

    Ok, Thanks
     
  5. blyons79

    blyons79 Well-Known Member

    I'd be interested in the oil slinger.
     
  6. agetnt9

    agetnt9 Agetnt9 (Dan)

    Whats the number on the side of that carb?
     
  7. AzChevs

    AzChevs Well-Known Member

    Rick, I found most of the parts, looking for one more piece. Do you need the A/C parts like the exterior suitcase with hoses and the inside box with control panel and all the A/C related parts? I have a few that I can choose from to come up with some nice looking stuff. Get back a little later today. Thanks
     
  8. AzChevs

    AzChevs Well-Known Member

    I have another 350 disassembled that I can check, let you know in a day. Thanks
     
    blyons79 likes this.
  9. AzChevs

    AzChevs Well-Known Member

    Its 7042944 KH 2581 under it
     
  10. blunozcruiser

    blunozcruiser Well-Known Member

    Any idea how long since it ran? Just wondering how gummed and varnished the carb is....
     
  11. rjm

    rjm Active Member

    Az, I think all I need are the compressor brackets and pullies, I'm going to use vintage air, or some other aftermarket kit. So I dont THINK I need anything else but I'm not sure. Thnaks again.
     
  12. AzChevs

    AzChevs Well-Known Member

    Rick, I didn't find the large mounting bracket, I have the ones on the compressor. I still have one more place to check tomorrow.
     
  13. AzChevs

    AzChevs Well-Known Member

    No, I drove the car off the trailer and that was it. It had vacuum leaks from missing hoses on the intake so I can not say it ran good or bad, just a cheap core.
     
  14. AzChevs

    AzChevs Well-Known Member

    Rick, No luck on the larger bracket that mounts to the underside and motor. I have the top large one, the bracket that mounts on the front of that to the compressor and the rear one. I can give you those for $50.00. The pulleys and brackets can all fit in a large flat rate box from the postal service for $18.85.
     
  15. rjm

    rjm Active Member

    Sorry AZ, been a little under the weather the past 2 days. How much do u want for the brackets you have and the 3 pulleys ?
     
  16. AzChevs

    AzChevs Well-Known Member

    Hope your feeling better. I can do all the pieces as a package deal for 100.00 shipped.
     
  17. rjm

    rjm Active Member

    Ok, sounds good, thx. And if you run across the lower bracket sometime, hit me up.
     
  18. AzChevs

    AzChevs Well-Known Member

    Did you want those parts and I can send an invoice. I believe it would be both pulleys you need for A/C, water pump and crank. Joe
     
  19. rjm

    rjm Active Member

    Yes, I thought I sent you a message, maybe I forgot to hit post. But, yeah I want them.
     
  20. AzChevs

    AzChevs Well-Known Member

    Pulleys sold to Rick. I also have another 350 2brl from a 1969 Skylark that is for sale in pieces since it was already taken apart.
     

Share This Page