Interested in radiator cross braces and mounts + hardware - price ? Upper rear seat panels - price ? Door windlaces - these are the "squishy" pads that fit between the rear lower panels and the door seals to them - they have a paper-like attaching behind the rear panels - condition and pricing ? Bench seat - is it a folding center ? condition of foam and power movement panel/switch ? price ?
Hey guys- had to make a quick trip down to the farm to switch vehicles. Couldn't stay long, but did jack the car up to check the posi, and look over the frame and other components people have expressed interest in. Posi appears to be a 2.93. Spun it and it didn't quite make 3 revolutions. Bench seat doesn't have fold down armrests. Pretty nice condition, though- a couple of small tears on the sides. Could be cleaned up and used as-is on a driver. Power unit works as it should. Tried it prior to removal. Seat foam and springs seem to be 100% intact. Asking $400 on it. Have power pigtail to the fuseblock to go with. Crossbrace is 100% intact, correct, all hardware. $50 Horns are there, not sure on datecode. Appear to be original to the car, though. Engine harness is completely intact. Missing a little tape down by the starter, but the plastic guard is intact. No cut plug ends. Voltage reg is there, intact, looks to be original, would clean up and restore nicely. Factory wire loom for the reg harness is intact. Not sure what to look for on the plastic radiator mounts- don't see anything appearing to match that description. The windlaces are intact, but have some minor cracking down low at the 90 deg bend. Hope this info helps. Also, the radio works. AM/FM, correct knobs, hardware, wiring. Front speaker and rear speaker as well. Thanks guys.
On the underhood wiring harnesses, I would do $150 + ship for all of it. Not one plug end is cut on any of it. This is for the entire harness set from under the hood. Engine/ac/headlights/horns. Voltage reg included. Also included is uncut/undamaged ground strap/bolt. ALL of the corrct plastic wire looms are there, and intact. I will do my best to remove them intact. I think there are 3 along the dr side fender, and 1 on the firewall. Also, I'd prefer to sell the rear interior pieces complete. They are all there, with all the hardware. No speaker cuts, top of the driver side one the sheetmetal is peeking out through the vinyl a little, but otherwise, these will clean up and be usable as-is. Tops, bottoms, lift cylinder cavity covers, courtesy light bezels/lenses. $175 + shipping. The A pillar covers are not perfect, but 80 on a 100 scale. There are small areas around the mount hole that have small cracks. Very small imperfections. Still have almost all of the convertible-specific stuff for sale. Stainless, rear seat, visors/brackets, top frame....
I would think this may fit in one of the US postal service's flat rate boxes? My zip is 02895 for JUST the engine harness. Thanks!
Chris, How much for the horns and the voltage regualtor with the loom attached (w/all mounting hardware) shipped to 15656. I will send you a pic of the plastic panels I was talking about. Thanks Terry
Armrest baseplate on driver side isn't very good. Has a chunk missing out of it about an inch and a half long. Pass side I will look. Thanks! chris
Chris- this was an AC car, correct? if so, price on the lower crank pulley(s)? Should be 2 large ones together and a smaller one behind them.. I can post a pic if you need one..
OK guys, an update on progress. Removed, inspected the convertible top boot retainer piece. It's nice with no damage. Plastic pieces on either side of the radiator are no longer there. I am working to get the harnesses out with the original looms intact. Horns are off, I will check on date codes. Pass side armrest baseplate is intact. Chrome is iffy. Crank pully, is real rusty. Can make out part #. $15 if you want it. I will post some pics if I can ever get a #$%# camera of mine to cooperate. WP pully is pretty nice #1375146 #111181 A/C comp complete/not stuck/clutch tight orig sticker/brackets pics coming. $175 all of it. All A/C components inside/out intact 7029242 LG carb Front cover Correct distributor Correct intake Thanks for the patience, guys! Chris ---------- Post added at 01:54 PM ---------- Previous post was at 01:49 PM ---------- Also.... Looks to be the original PS pump. Brackets, pump, looks like the original cap, hoses, and pulley. Pulley #1386935 All/$150 Complete AM/FM. I mean all attaching hardware, knobs, and radio bezel. Pics to come. $200 Still have posi, back seat is pending to John, other convert stuff is still there except power top unit and w/s stainless. Nice dash. Nice carpeted black ac kickpanels. Power bench seat. Much more. chris
Chris- this is what it should look like... Again, I think this set up and the engine wiring harness should fit in a larger size USPS flat rate box..
George, the pully is pretty rusty, but not bent. I'll just toss it in the box since you're buying the harness. Thanks! Chris
OK- update Posi sold. Horns read 9000 12v 491 8K2 E/F Have radio, can send pics- shined up real nice. Chris
Could I get Pics, of the Black interior panels & Rear seat ? Please send to: jeffthompson_j7@yahoo.com Thanks again, Jeff
Chris, Are you selling these parts? I'm still interested in the convert. boot track, as per our previous correspondence. Please update. Thanks, Matt
Hi Chris, IF you decide to separate: I'd like the A/C duct (pic attached - in case my wording is incorrect. I'm referring to the part that directs air into the A/C dash vents). Also looking for a A/C climate control unit. Finally, randomly, the glove box lock if useable. Would need to be shipped (97221 - can figure that part out later). Thanks! Zach