SNIPER EFI on my Twin Turbo SBB

Discussion in 'High Tech for Old Iron' started by Sebambam, Jan 3, 2021.

  1. Max Damage

    Max Damage I'm working on it!

    Ok, so the Driver side stock manifold feeds a U shaped pipe thats loops around and joins the passenger side manifold and they both feed the Turbo. Thanks for the visual aids!
     
    sean Buick 76 likes this.
  2. sean Buick 76

    sean Buick 76 Buick Nut

    And although it may seem very restrictive this provides plenty of flow to use a 650hp buick 350. And my plan would be to just provide the custom manifold with V bands on both ends so people could just have an exhaust shop bend pipes and weld on a turbo flange. That way people can do any turbo placement they want, and it’s only a small manifold to ship. One reason to do this is that the drivers side is super tight with any turbo header or manifold as the steering shaft is there. This eliminates that issue. It also reduces the chances of broken bolts as only the one manifold is removed. And it allows people to setup any turbo etc that they want to.

    when mark sold full kits it was a hassle to make everything fit each car and peoples desires.
     
    Last edited: May 22, 2021
  3. Max Damage

    Max Damage I'm working on it!

    It seems like it radically simplifies installation, as there is more space on the passenger side to accommodate the turbo and plumbing? Do use a larger single turbo unit (versus the twin turbo installs)?
     
    sean Buick 76 likes this.
  4. sean Buick 76

    sean Buick 76 Buick Nut

    yes there is lots of room on the passenger side unless you have AC. And yes a GT-45 turbo or similar would work fine.
     
    Lucy Fair likes this.
  5. Sebambam

    Sebambam Well-Known Member

    Yes Sean is right it shouldnt be a problem at all with the "room"

    check VSracing for a t4 turbo
    Even any cheap T4 turbo will give you a lot of power that your "stock-ish" engine can handle but need to diagest :)
     
  6. Sebambam

    Sebambam Well-Known Member

    Friday night, booze and V8s
    Finished the fuel system and Ignition.
    Slowly but surely
    20210611_201721.jpg 20210611_201732.jpg
     
    patwhac likes this.
  7. sean Buick 76

    sean Buick 76 Buick Nut

    I like that look! Now that I’m on E-85 I may go that route and eliminate the air to air intercooler.
     
    Sebambam likes this.
  8. Fox's Den

    Fox's Den 355Xrs

    Nice Job looks good Great Look. Nice neat installation. Best looking one on here
     
    Sebambam likes this.
  9. Sebambam

    Sebambam Well-Known Member

    Just needs to perform ;)
    I am confident
     
  10. Fox's Den

    Fox's Den 355Xrs

    So am I can't wait to hear it !!
     
    patwhac likes this.
  11. Sebambam

    Sebambam Well-Known Member

    Some progress today.
    Custom driveshaft is in. As well as the 3" xpipe.

    I saw somebody was asking about 28x10.5 on 10 inch on a Stepchild.
    BS 6", longer wheel studs, 1/4 spacer makes it 5.75 BS , rear shock lower mounts relocated. Stock 8.5 rear ( posi build)
    It clears!
    20210710_091358.jpg 20210710_091136.jpg 20210710_091333.jpg
     
    Fox's Den and patwhac like this.
  12. sean Buick 76

    sean Buick 76 Buick Nut

    Looking good
     
  13. Mart

    Mart Gold level member

    Saw this Cutlass at car show today. Was his grandpa's car. He put the whole drive train from a rusted out 86 T-type for $4,5k. Said it fit perfectly. No problems, no custom stuff needed. Says It runs fantastic. Increasing boost says it will be 600hp +.
    This seems like the way to go for perfected turbo power to me, rather than 350 turbo conversion. :)
     

    Attached Files:

    Mark Demko and patwhac like this.
  14. Fox's Den

    Fox's Den 355Xrs

    Looks like it belongs there.
    do this to a 4 door sleeper, 11 sec monster
    wonder how much you can get all this for at the junkyard hmmm...
    or get you a TA aluminum block and start your own rest is easy to get this,
    would be cool in a Skylark non GS car.
    more like killer
     
    patwhac likes this.
  15. Fox's Den

    Fox's Den 355Xrs

    Might want to put a air bag in that right rear spring with about 15 lbs in it.
     
    Sebambam likes this.
  16. Sebambam

    Sebambam Well-Known Member

    Let's see how she squads 1st. The I ll adjust
     
  17. Buick#455

    Buick#455 Well-Known Member

    Update??
     
  18. Sebambam

    Sebambam Well-Known Member

    Hey Bud' not much been working like a pig... but you are right i have to get going...the todo list is getting smaller ...
    i was trying to sort out a cheap throttle cable option but i guess i just buy a adjustable cable and a FAST mount that works with the Snipers.

    Then i should be close to starting it up... maybe this upcoming weekend
     
    Max Damage likes this.
  19. Buick#455

    Buick#455 Well-Known Member

    Can’t wait!
     
  20. Sebambam

    Sebambam Well-Known Member

    thanks to your Ass kick i was able to finish the throttle cable. Filled up fluids, charged the battery, and updated the EFI firmware. I noticed that the starter either dont catch or doesnt engage i am off tmrw so i might have a night off beer and wrenching and MAAAAYBE i start her tonight.!
    wish me luck ahahahah
     
    Max Damage likes this.

Share This Page