Kenne Bell Cams

Discussion in 'Parts for sale' started by 462bbbcamaro, Dec 16, 2010.

  1. 462bbbcamaro

    462bbbcamaro Well-Known Member

    I have 2 cams that have been sitting boxed up on the shelf that I do not need and since I am looking to help finance other stuff I want for the car I am selling these. Both cams are used but in excellent condition and were broken in properly with good distributor gear teeth.

    Cam #1: KB118 with matched Rhoads Lifters (and labeled to go back on each proper lobe) with original cam card. I ran this for a short while. It ran great and made a ton of torque but had way too smooth an idle for a car with a full cage and a race look. If you want great vacuum and a mellow idle with just a hint of lope, great low-end, killer mid-range and will pull real nice to over 5,500 this combo is for you.

    For those unfamiliar with Rhoads Lifters there is a description here: http://www.summitracing.com/parts/RHL-9698/

    Looking to get $175 + shipping or better yet I am looking for a possible trade full / partial trade on a switch pitch convertor with more stall for my TH-400 (at least 3,000).

    Cam #2: KB 107/118 I was looking for a window rattler to replace above cam and bought this already used and without a cam card. I was gonna sell this some time ago but I didn't as I didn't know exactly what was and didn't want to misrepresent it. It is stamped KB-MK C107. It is also stamped 1185 which made me suspect it to be the 118 degree lobe separation version and was later confirmed to be so by a friend who is very respected in the Buick community.

    Anyway, I found a 107A cam to run instead so I don't need this one. I never installed it. The 118 degree separation this cam has gives it a milder idle and better vacuum and better manners than the really radical 107 degree version I wanted. This cam still has a killer lope and there have been a number of guys in the 11's with one.

    I paid $75 + shipping for it so I am asking the same, I am just hoping to recoup my investment by someone who this cam is better suited to their combo than it was mine (I wanted more radical).

    I tried to post pics with this thread but couldn't figure out how to sesize them to 800x800 pixels. So I have multiple pics of each available I can email upon request. Thanks for looking :beers2: Todd
     
  2. Thumper (aka greatscat)

    Thumper (aka greatscat) Well-Known Member

    Chris R. might be interested in the 107,so I'll get in line for him.I'll contact him today.
    gary
     
  3. 462bbbcamaro

    462bbbcamaro Well-Known Member

    Great thanks Gary! Let me know :beers2:
     
  4. arczuma

    arczuma Active Member

    Do you still have the 118, I'll take it. Al
     
  5. 462bbbcamaro

    462bbbcamaro Well-Known Member

    Hello Al. Yes I still have it. Where are you located? I'll try to figure out shipping. Todd
     
  6. arczuma

    arczuma Active Member

    Hi Todd, I'm in Rhode Island zip 02878. Al
     
  7. 462bbbcamaro

    462bbbcamaro Well-Known Member

    I sent you a pm Al :beer
     
  8. 462bbbcamaro

    462bbbcamaro Well-Known Member

    118 cam and Rhoads lifters sold. 107/118 cam still available.
     
  9. C.Rob

    C.Rob Well-Known Member

    I will take the other. Thanks Gary.
     
  10. 462bbbcamaro

    462bbbcamaro Well-Known Member

    pm sent
     

Share This Page