Nylon fasteners for Qtr and door trim mouldings

Discussion in 'Parts wanted' started by scubasteve455, Mar 30, 2018.

  1. scubasteve455

    scubasteve455 Well-Known Member

    The thin mouldings that go below Qtr glass and door glass to the door mirrors
     
  2. scubasteve455

    scubasteve455 Well-Known Member

    Both sides of car (4) mouldings I need (2) dozen
     
  3. Matt Knutson

    Matt Knutson Well-Known Member

    Do you have a sample?
     
  4. taf44667

    taf44667 69 Vert 4-Speed

    Yeah, need a pic - Not sure what you are explaining/looking for to help.
     
  5. DasRottweiler

    DasRottweiler -BuickAddict-

    If it is what I think you are talking about, I need 5 or 6 to mount my passenger door piece. Lemme know ifya find a source for the correct plastic piece.....peak moldings, yes?
     
  6. hugger

    hugger Well-Known Member

    Upper peak moulding yes
     
  7. JoeBlog

    JoeBlog Platinum Level Contributor

  8. flynbuick

    flynbuick Super Moderator Staff Member

  9. mrolds69

    mrolds69 Still restoring!!!

  10. scubasteve455

    scubasteve455 Well-Known Member

  11. scubasteve455

    scubasteve455 Well-Known Member

  12. scubasteve455

    scubasteve455 Well-Known Member

  13. scubasteve455

    scubasteve455 Well-Known Member

    Have these coming smaller size. But would like nylon ones
     
  14. DasRottweiler

    DasRottweiler -BuickAddict-

    The metal pop-in fasteners with the tail are for the quarter window pieces.
    The doors have plastic slide-in fasteners that clip onto studs on door. No studs, no problem, I bought replacement screw-in studs for the doors. I'm just short the plastic clips for passenger door. Jim
     
  15. scubasteve455

    scubasteve455 Well-Known Member

    Jim where can I get the replacement screw in studs for the door. My doors are not original to the car.
     
  16. scubasteve455

    scubasteve455 Well-Known Member

    This car was a Fremont Ca. Plant car. So these fasteners might differ from Flint. Mi.
     
  17. DasRottweiler

    DasRottweiler -BuickAddict-

    http://www.thefastenerwarehouse.com/page/page/584919.htm
    I bought a bag of screw-in studs to replace a few missing windshield studs and also to mount the peak moldings to the doors.
    I can mail you 14 of them , that's enough to do both doors. If you find the right plastic clips, lemme get 7 of them if you would?
    I need to go thru my plastic clips and I can at least tell you which ones I purchased that did not work. I used old , original clips to mount my driver door peak molding. I will PM you tomorrow with that info. Jim
     
  18. DasRottweiler

    DasRottweiler -BuickAddict-

    20180211_161740.jpg

    The holes for the quarter window peak moldings are 5/16" if I recall correctly. Start small , work up to the final size. I actually drilled holes in a junk fender to test fit snap-in metal clips.
    I started my screw-in stud holes with 1/16" drill bit. Hope this helps....Jim
     
    Last edited: Apr 7, 2018
  19. DasRottweiler

    DasRottweiler -BuickAddict-

    Close but not quite. The original ones I used have little wings that space the clip off the car to keep clip tight in moldings.
    They may work but I have similar ones that don't. I actually have quite the collection going , of the wrong clips, unfortunately. ......Jim
     
  20. BrianTrick

    BrianTrick Brian Trick

    I need a complete set of these too. I bought a car as a painted shell,and it has the holes for this peak molding. I was able to buy the peak molding from another member,but now I need all the fasteners.
     

Share This Page