Possibly Attending The BPG .List of Parts to be SOLD

Discussion in 'Parts for sale' started by nickbuickgs, Jul 25, 2012.

  1. nickbuickgs

    nickbuickgs nickbuickgs

    I have not made a decision on attenting this years BPG . However the parts listed here are For Sale on the Board. I will be taken everything to the event if attending . I will Keep you posted ! If you dont see it just ask, Who knows :Do No:. Most of my 1970 parts I will not be selling ....

    Samll reproduction parts

    4 speed speedo Cable Clips 30.00 pair
    400-455 Engine Mount heat sheilds 15.00 plated
    Heater Hose wire Ties Long 12.00 & short 8.00 plated
    400-455 Power Brake Booster line clip 16.00




    1969-72 Firewall Clutch plates Blasted & painted (bolted to the steering shaft) 25.00 each
    1969-1972 4 Speed Pedal set up with repaired firewall rod. (I have to check on the switch) possible... 350.00
    1970 455 Fender emblems NOS 40.00
    1970-73 Wide & narrow pin STAGE 1 original emblems Clean used couple of sets 15.00 each
    1973 NOS Stage 1 norrow pin 60.00 pair
    1969-70-2 Lt Blue Sport Wheel Horn Cap Nice 70.00 obo
    1969 NOS Full GM 1/4 panels pair 3000.00 Pair only
    1968-70 A/C Top Brackets Blasted & Powercoated 25.00 each
    1968-70 Lower A/C Aluminum Brackets 10.00
    1968-69 Hood pull-releases plated Yellow 10.00
    1969 350 metal heat tubes 2 each 10.00
    1969 350 Air cleaner support painted 40.00
    1970 GS Black Bucket seats RE-covered & Lighted for race car . (Fixed Tracks) Can be converted to factory slide track... Mint !400.00 pair
    1969-72 2 sets Bucket seat cores & plastic parts 100.0 each
    1969 Front straight bumper cores 2 each 50.00

    T/A SP-1 Dominator Intake for 400-455 Mild port matching 300.00
    Holley 850 double pump 4781 Carbs Milled air horn & air bleads added 2each 200.00
    Stinger S-4 Ignition set up complete 250.00
    1971-2 Tail lamp lenses Nice with harness . I broke the corner of one lens . I should have the piece to repair 60.00
    Tall Moog cargo springs for Wagon or GS 40.00
    Hurst Aftermarket Bench Seat Shifter & rods levers for 1966-68 Muncie . These have a smaller slot that bolt to the side case 100.00
    Various years of Buick 400-455 Distributors & 1 HEI unit 10.00ea 25.00 HEI
    2 1000 SERIES Thermoquad carbs Great for nostalgic look with chokes 350.00/300.00 (1 has been restored .
    1969 SKYLARK Rear trunk moulding.. Beautiful Arizona Crome No PITTING 100.00
    1971-up Timing covers BIG PORT 5/8 2 for sale 85.00 ea

    More to be listed !
     
  2. Matt Knutson

    Matt Knutson Well-Known Member

    Interested in line item #3 Sadly, I can't make it to the show, however, if correct 70 emblem I'm very interested.

    Thanks, Matt
     
  3. Lemans1

    Lemans1 Well-Known Member

    If the springs fit my 67 wagon, I'm interested. I will be at bpg.
     
  4. ajesh35

    ajesh35 Well-Known Member

    Nick would like the upper and lowere ac bracket also the 69 deck trim let me know if your going to be at the show
     
  5. nickbuickgs

    nickbuickgs nickbuickgs

    The NOS stage 1 emblems are narrow pin 73-75

    ---------- Post added at 05:58 AM ---------- Previous post was at 05:58 AM ----------

    Ok will do
     
  6. Thumper (aka greatscat)

    Thumper (aka greatscat) Well-Known Member

    Interested in a 4speed setup,everything minus the pedals,do you have that included in item 2? If not do you have these parts?Zbar,clutch fork,clutch fork ball,clutch rod,zbar engine ball and nylon ball,spring,etc.
    gary
     
  7. Matt Knutson

    Matt Knutson Well-Known Member

    To be clear - are they 455 emblems or St 1 emblems? I'm intereted in 455 emblems.

    Thanks, Matt
     
  8. nickbuickgs

    nickbuickgs nickbuickgs

    I have a set of 455 fender NOS & Stage 1 norrow pin

    ---------- Post added at 04:21 PM ---------- Previous post was at 04:18 PM ----------

    Send you a pm
     
  9. copperheadgs1

    copperheadgs1 copperheadgs1

    Nick, What is a firewall clutch plate(bolted to the steering shaft? You have me stumped. IS it the split plate that the shaft and rod pass through?
     
  10. Duane

    Duane Member

    Dave,
    That is the way I understand it. The automatics have no hole in them.
    Duane
     
  11. Billy Baker

    Billy Baker Member

    sent a pm about seats.
     
  12. nickbuickgs

    nickbuickgs nickbuickgs

    Yepper
     
  13. Lemans1

    Lemans1 Well-Known Member

    Nick, have you decided whether or not you will be going to BPG?


    Rick
     

Share This Page