70 Cast Iron Intake

Discussion in 'Parts wanted' started by flynbuick, Jun 22, 2005.

  1. flynbuick

    flynbuick Guest

    L Code 70 455 Cast Iron Intake Needed

    We need a 70 cast iron intake(#1231718) with a date code of L. That translates to November 69.
     
    Last edited by a moderator: Jun 24, 2005
  2. GStage1

    GStage1 Always looking for parts!

    I believe Jim needs one for his 455, not a 350.
     
  3. flynbuick

    flynbuick Guest

    Yes thanks for clearing that up.
     
  4. Floydsbuick

    Floydsbuick Well-Known Member

    Were do I look for these codes?
     
  5. flynbuick

    flynbuick Guest

    The number above and the date code are on top towards the front and obvious. They are raised and cast into the block.
     
  6. Thumper (aka greatscat)

    Thumper (aka greatscat) Well-Known Member

    I have one with a K-28 code.
    gary
     
  7. flynbuick

    flynbuick Guest

    Gary

    Thanks so much for responding. I will take it if I do not get a closer number. I would appreciate it if you would give me a bit of time.
     
  8. StratoBlue72

    StratoBlue72 Well-Known Member

    Hi Jim,
    I think I have a 70 455 intake but will have to look at the date code. In fact I think I may have sold you the choke thermostat out of it.
    Tim
     
  9. flynbuick

    flynbuick Guest

    Tim

    You did sell me one.
     
  10. Thumper (aka greatscat)

    Thumper (aka greatscat) Well-Known Member

    No problem,its just sitting ,and it does'nt eat anything.
    gary
     
  11. Ray

    Ray Well-Known Member

    intake

    i have a 70 intake off a electra 455 not sure of number i will look tonite and post it tommorrow.thanks Ray
    ________
    Magic flight launch box review
     
    Last edited: Apr 15, 2011
  12. MRehr

    MRehr Well-Known Member

    intake

    I have a B-1231718-E, D-24, Saving for that stock appearing, right. Let me know if the code is correct. Mark :)
     
  13. flynbuick

    flynbuick Guest


    Yours is April 24, 1970 which is too late for the 2nd week of December, 1969 build date for the car in question. We do appreciate you looking though.
     
  14. flynbuick

    flynbuick Guest

    Joe

    I am going to have to consult with Duane on that one but my instinct is that I have never seen one on a car that falls in the same week as the build week date. As you know that intake date is also in the second week of December. I have seen them as early as the week before. But I am going to ask him his opinion. If it was dated three days earlier I would take it.
     
  15. Dan Healey

    Dan Healey Well-Known Member

    Jim

    I think you need an "L", M8 is darn close and almost works though... :(
     
  16. flynbuick

    flynbuick Guest

    Yes I have since learned that is L is really what I need. If not Gary's late K will have to do. But we have time to see if an L will show.
     
  17. Scott Miller

    Scott Miller Guest

    Jim,

    My 01B built 70 Stage 1 car has a M 8 intake. :)
     
  18. flynbuick

    flynbuick Guest

    Scott

    That is about what I have seen --about a 30 day lag.
     
  19. i havd a j coded one
    Greg
     
  20. flynbuick

    flynbuick Guest

    Greg

    That is September, 69 and a little too early for our needs. We appreciate you looking though.
     

Share This Page