Cleaning out the garage, these need to go. They are spares or takeoffs from when I did my '68 about 10 years ago. These are priced to go just like a swap meet, local pickup will be best. I will only ship if you are willing to pay my cost and time to do so. Buy this stuff up so I don't have to throw it out, make offers and bundle! 15x7 wheels, 4-3/4 bolt circle for GS. Decent chrome - $30 pair '68 GS grille surround - light pitting, $15 Interior rearview mirror w/trim, good chrome, glass cloudy - $3 Brake pedal pad, I think this is a spare repro that I bought - $3 Miscellaneous stainless trim including partial drip rail, rear window. Incomplete and beat up - $5 Older GSCA "Popular Mechanics" cam w/lifters, used. - $25 Miscellaneous "box-o-gaskets" with multiple water pump, oil pump, exhaust, valve cover, etc. -$5 Taillight lenses, both damaged, usable for a driver - $5 pair HV oil pump kit, used - $10 Oil pump cover, minimal scoring - $3 Rear drums, used, 80k miles, replaced with aluminum - $15 pair Q-jet spacer, 1" open aluminum - $8 Early aluminum rocker assenblies, used, one set ground for spring clearance - $30 both sets Miscellaneous "box-o-stuff" with used doorhandles, antenna stub and wire, nuts-n-bolts, etc - $5 Stock fuel line, pump to carb, straight but surface rust - $5 Q-jet core, gaskets, and parts - $15 Converter, stock stall, core needs rebuilt - $5 Water pump, used, takeoff when I restored the A/C and found I had a long pump and needed a short one. - $5 Crank pulleys, two sets - $3 both balancer, I think this is a '75 up because I see blue paint - $5 A/C temp control for parts - free to the first request, somebody gave it to me.
<< Stock fuel line, pump to carb, straight but surface rust - $5 >> << Q-jet core, gaskets, and parts - $15 >> First in line on these. PM me with shipping to zip code 55079 please. Thanks!
interested in wheels. can i get a couple close-ups ? Shpg to Maine 04257? You can tape both boxes together to save a little. Wacko
1st up for ,...455 GSCA pop cam:::whats the specs and how many miles...and early rockers,.I assume 68-69 rockers for 455 :: could I get a closer pic of them and do you have the hold down tabs and bolts,.. and the water pump ,..its a long nose pump, correct ,.. is the bearing tight.. thanks jerrold,..
2nd in line on the wheels please. Also, where are you located? (Im using tapatalk and it doesnt show the header with your location)
Hey John Do you have any front bucket seat cover buttons? the rear seat buttons may be the same? gary
UPS ground is $12.86, could do USPS small flat rate box for $5.50 if it would fit, not sure it would. I'll take Paypal. ---------- Post added at 11:40 AM ---------- Previous post was at 11:38 AM ---------- PM Sent ---------- Post added at 11:41 AM ---------- Previous post was at 11:40 AM ---------- Sorry, no seat cover buttons. ---------- Post added at 11:44 AM ---------- Previous post was at 11:41 AM ---------- Wheels shipping to you would be $64 UPS ground, total $94. I'll post pics later, have to dig these back out. ---------- Post added at 11:55 AM ---------- Previous post was at 11:44 AM ---------- The cam has about 3 years and probably 15k miles on it. Some wear on the distributor gear, I ran it with the HV oil pump. Swapped out for a Scott Brown cam, it ran when I pulled it. I can't remember the specs, it's a split pattern with more exhaust than intake duration. Bought direct from GSCA about 10 years ago. Two sets of rockers, one 400, one 430 these never came on a 455 as far as I know. They do fit and work 455, give a little more rocker ratio than the steel units. These are USED, one set clearance ground for springs, one set a takeoff from the yard complete with grime. I can't say for sure on the tabs and bolts, may be missing some. I am also not clear on the pump, it's the opposite of what a '68 GS with A/C needs 'cause I pulled it and put on the right pump when I put my A/C back on the car. The bearing is tight and it did not leak when I took it off. ---------- Post added at 11:57 AM ---------- Previous post was at 11:55 AM ---------- Shawn, I'm in Grand Haven MI 49417. Shipping the wheels to Dayton is probably going to run about $60 based on the UPS quote I got for the earlier buyer. I'm waiting to see if he wants to go ahead. ---------- Post added at 11:59 AM ---------- Previous post was at 11:57 AM ---------- It looks good enough to stop the car Seriously, it's not worn and probably as good as what they put on these cars back in the day. It is for an automatic, wider type, not for a stick car. ---------- Post added at 12:01 PM ---------- Previous post was at 11:59 AM ---------- Good to hear from you Steve. I'll let you know if you get to the head of the line. ---------- Post added at 12:07 PM ---------- Previous post was at 12:01 PM ---------- I have your PM, I'll post pics. Shipping would be about $15 depending on your zip code.
john,.. I will pass on the cam,...about the rockers,.. are the valve tab ends in good shape on both sets and not beat to death... I will take the water pump.. Sorry for the Questions John... thanks again..jerrold
Thanks john, i will take the brake pedal pad. My concern was mainly do they fit well. Its for an auto car.
I'll pick a box up on the way home today, they are free at the post office. Let you know tomorrow if the spacer will fit. ---------- Post added at 11:47 AM ---------- Previous post was at 11:46 AM ---------- Wacko, They are yours if you want them, I did not have a chance to take pics last night, I'll do that tonight.
