Small interior trim piece-what is it called and where can I get one?

I was driving down the freeway yesterday and the small trim piece at the base of the windshield popped off and I can't find the damn thing. It's about 1.5" long and covers where the two long pieces of windshield trim meet. I've searched the entire interior of the car so it may have gone out the window. Can someone please tell me what the little piece is called and where I can buy another one? Thanks....

 

Maybe Bob's Automobilia
or, Ebay on a car part out.

I don't think I have an extra. But, I'll take a look in my stash of parts

Edit: I don't know what to call it either

 

https://www.danchuk.com/danchuk1.aspx?Id=1f55e341-4539-4280-b714-6f0a049fc2ae

Check this Danchuk Chev site out, they call it an "Interior Lower Windshield Centre Moulding Connector". It may even fit?

Pictures below are of mine, you may even be able to fabricate one.




Front face with screw hole is 1" wide x 1 3/8" with a slight kink
Rear side is 1" wide x 7/8" high
Tab off front face is 1/8"

 

Thanks to James and Ross for the replies. Fabricating one doesn't sound like a bad idea. I didn't fill out all my info on the Danchuk site to see how much shipping would be but I will later if I can't make one. That's pretty cool that Ross, who lives in New Zealand, has an American tape measure. Thanks again....

 

Danchuk wants $13.63 to ship that tiny little piece to me. The piece is $6.95 which is reasonable but I'm not going to pay almost twice that amount for shipping something that probably weighs less than an ounce. I'll make one out of a piece of old license plate before I let them rip me off that badly....

 

I didn't get the chance today to go to look in my storage for the piece.
It'll be later this week, I'll have to work out of town for a couple or three days

And, then I'm not sure if I have an extra...
I'll let you know later this week

 

If you have one that would be great but in the meantime I gave up on the license plate idea and used the top of a small Buss fuse container-the kind with the metal top over a small plastic container that holds 5 of the old fashioned fuses. It fit in there pretty well so I drilled a hole in the middle of it and then I took the advice of the Rolling Stones to "Paint It Black." I'll take a pic tomorrow after I install it and I'll post it here....

 

Cool !!!

 

I think it turned out pretty good.... :TU:

 

I have a few that I don't need.

 

How much do you want for one with shipping to zip 40010? Do you have a Paypal account?

 

free...as soon as my eyes heal

 

Eyes healed (got stung in face by wasps while removing from parts car). Send your contact info by PM or email.

 

That's no fun at all, hope all is well now.

 

Ouch!!
I took a bumblebee sting to the forehead once
It's has on the eyes

 

PM sent earlier this evening. Thanks....

 

I picked up the piece at the post office today and put it on the car. It didn't go on exactly straight because one of the trim pieces that it covers sticks out a little farther than the other. It looks a lot better than the top of a Buss fuse holder so thanks again to Willie for sending it to me free of charge. When I was in the garage taking the pic I saw a deer out front so I took a pic of that too....

 

Yesterday, I noticed mine is a little crooked, too.
I think it's always been that way

 

Loosen all the screws center and side pieces, line up the center and tighten, then tighten the sides. If it still pulls the center out of place, find the offending screw, remove it and drill another hole.
The factory probably just threw all the pieces up there, drilled some holes and then stuck the screws in.